Plating onto Plastics
ProPlate® metallizes plastics for electronics, semiconductor, aerospace, medical, and energy applications, combining PVD, wet chemistry, and electrolytic plating to turn molded, machined, extruded, or printed polymer parts into fully functional metal-surfaced components.
Plating onto plastics allows a molded, machined, extruded, or printed polymer part to perform like a solid metal one at a fraction of the weight and cost. ProPlate metallizes thermoplastics ranging from general-purpose ABS to high-temperature PEEK and Ultem®, depositing copper, nickel, gold, platinum, and other finishes directly onto the surface. ProPlate does not run a single plating process for every part. We select and combine physical vapor deposition, wet chemistry, and electrolytic plating based on the resin, the geometry, and the production volume, then converge both paths on one qualified finish and one validation protocol.
Every finish we apply is functional. Plated plastics carry current, hold a low and stable contact resistance, catalyze reactions, shield against interference, and resist wear and corrosion. Because the plated shell does the work and the polymer only holds the shape, a metal part can be redesigned as a plated polymer one without giving up performance, often at a significant weight savings that depends on the geometry and the metal being replaced.
Why Choose Plating onto Plastics?
Dramatic Weight Reduction
Thermoplastics are roughly six to eight times less dense than stainless steel, brass, or beryllium-copper. Because the working duty is carried by a plated layer only microns thick, converting a machined metal part to a plated polymer one has removed as much as 80% of its mass on programs we have run, with no loss of current-carrying capability. The exact reduction depends on the geometry and the metal being displaced, so we present it here as an example rather than a general rule.
Lower Cost at Volume
Machined metal parts are produced subtractively, one at a time, and their cost is bound by machine-hours. A molded polymer core is produced net-shape. Once tooling is amortized, the cost of each additional part drops sharply, which is decisive on programs running hundreds of thousands or millions of components.
Design Freedom
Features that are slow, expensive, or impossible to machine can simply be molded in. Plating on plastics opens geometries that a subtractive metal route cannot practically reach.
Engineered Surface Performance
Electrical conductivity, stable contact resistance, catalytic activity, solderability, EMI and RFI shielding, thermal management, and wear and corrosion resistance, all engineered to the application rather than pulled from a catalog.
Evaluating ProPlate for a plated polymer program?
How ProPlate Plates Plastics
The difficult part of plating onto plastics is not building up the metal. It is establishing a durable, adherent first layer on a polymer that was never designed to accept one, and doing it the same way on every part, in every lot. That first layer is where the engineering lives, and ProPlate holds a qualified surface-treatment and activation process for each resin we support.
ProPlate reaches that first layer by more than one route, selected by resin chemistry, feature size, and volume.
Wet Chemistry Metallization
A qualified aqueous process prepares and activates the polymer surface so it will accept an initial metal layer. Wet chemistry suits high volumes of small parts and adapts well to barrel and Spouted Bed Electrode (SBE) plating.
Physical Vapor Deposition (PVD)
A seed layer establishes adhesion and conductivity physically rather than chemically, which brings chemically inert polymers into reach. Most plating on plastics suppliers offer only a wet chemistry route, and their resin range is limited accordingly. ProPlate has also developed custom tumble-PVD fixturing that seeds very small components uniformly on all surfaces, which is what makes micro-scale parts practical at volume.
Laser Direct Structuring (LDS)
Laser direct structuring takes a different path to the same goal. Instead of metallizing an entire surface, an LDS-grade resin is molded with a laser-activatable additive, and a laser traces the exact pattern to be plated onto the finished part. Only the traced areas become receptive to metal. Metallization then follows that pattern precisely, leaving the rest of the part untouched.
The result is selective, three-dimensional metallization: conductive traces, antennas, and circuit paths applied directly to a molded component with no separate circuit board, no flex, and no assembly step. It gives design engineers a way to put electrical function onto a part that also has a mechanical job to do, and to change the trace pattern without changing the tool.
LDS is limited to resins formulated with the laser-activatable additive package, which is a narrower list than the substrates we plate conventionally. ProPlate can advise on whether LDS or a conventional metallization route is the better fit for your component.
Electrolytic Plating
Once the surface is conductive, the functional finish is built electrolytically to the thickness and composition the application requires. Adhesion of the plated layer to the polymer substrate is verified to ASTM B571.
Combination Processes
Most programs use a combination route: a PVD or wet chemistry seed followed by electrolytic buildup. ProPlate selects the seed route to fit the resin and the part, then converges both paths on the same finish and the same validation protocol.
Engineering Plastics We Plate
Every resin behaves differently, so every resin carries its own qualified process. Rather than claim we can plate any plastic, ProPlate maintains a defined portfolio of qualified substrates and qualifies new ones to customer specification.
| Resin | Typical Use |
|---|---|
| ABS | General-purpose molded components, housings, connector bodies |
| Topas® (COC) | Precision micromolded parts and tight-tolerance features |
| PEEK | High-temperature, high-load applications |
| Ultem® (PEI) | High-temperature, dimensionally stable structural components |
| LCP | Fine-feature, high-frequency, and high-density interconnect |
| PET | Cost-sensitive and flexible components |
| PEBAX® | Flexible components requiring metallization |
| TPU | Flexible, abrasion-resistant components in wearable and consumer-adjacent hardware |
| Nylon | General-purpose structural and housing components with good toughness |
| Polyurethane | Flexible and impact-absorbing components requiring a metallized surface |
| Polyimide | High-temperature, high-performance films and small precision components |
| Noryl® (PPE/PS blend) | Dimensionally stable components needing good electrical insulation and low moisture absorption |
Not seeing your resin or material? ProPlate qualifies new substrates to specification.
Metal Finishes on Plated Plastics
ProPlate plates gold, platinum, silver, rhodium, palladium, palladium-nickel, nickel, copper, and tin-lead. On a polymer substrate, the finish is chosen for what the surface has to do:
- Gold for low, stable contact resistance and corrosion immunity on separable and mating contacts
- Platinum, including high surface area platinum black, for catalytic and electrochemical performance
- Copper for base conductivity and as the foundation of most build-ups
- Nickel as a barrier layer and for hardness and wear resistance
- Silver for high electrical and thermal conductivity
- Palladium and palladium-nickel as an alternative barrier layer to nickel
- Tin-lead for solderability in specific industrial applications
Not sure whether your material can be plated? Our team can tell you.
Applications for Plated Plastics
Semiconductor and Electronics
Spring probes and pogo pins, compression test sockets for automated, burn-in, and system-level test, LGA sockets, board-to-board and mezzanine connectors, high-speed backplane and power-delivery contacts, and EMI and RFI shielding on molded or machined housings. High-density interconnect programs, where a single package can carry thousands of contacts and a rack carries millions, are where plated-polymer economics are strongest.
Catalytic and Electrochemical Components
Plated plastics are not only about carrying current. A high surface area platinum deposit on a molded or machined polymer element creates a catalytically active surface, allowing a lightweight, low-cost molded part to drive a chemical reaction that would otherwise require a solid precious metal component. ProPlate metallizes molded or machined polymer elements for catalytic, sensing, and electrochemical applications where surface activity, rather than bulk material, does the work.
Aerospace
Lightweighting of connector bodies, housings, and structural components where mass carries a direct performance cost, plus EMI and RFI shielding and corrosion protection on molded or machined assemblies.
Advanced Compute and Quantum Systems
Control electronics and cryogenic test hardware rely on the same high-density contact technology as AI data center infrastructure, at volumes where plated polymer components materially change both cost and mass.
Energy and Industrial Systems
Battery contact springs, charging connectors, industrial sensor housings, and control system components, where corrosion resistance and conductivity matter more than bulk metal, plus EMI and RFI shielding on molded or machined enclosures in harsh operating environments.
Medical Applications
Looking for medical device applications of plating on plastics? ProPlate’s Meta-Poly® polymer metallization platform covers catheter, balloon, and implantable-grade metallization in depth.
Application Examples & Technical Resources
Plated-Polymer Pogo Pins for AI Data Centers
Millions of tiny spring-loaded pogo pins let the silicon in AI data centers be tested, socketed, and serviced without solder, and at hyperscale volumes the cost and mass of each pin become first-order economics. ProPlate applied its Plating onto Plastics platform to replace machined-metal spring probes with net-shape micromolded, fully metallized contacts. The result was a pin roughly 80% lighter at lower unit cost, with the full electrical and mechanical performance of a machined metal probe.
The Product: Plated-Polymer Pogo Pins
A pogo pin, or spring probe, makes a compliant, low-resistance joint under compression. Inside a hollow barrel, a sliding plunger rides on an integral compression spring that develops a controlled normal force against the mating land. The spring provides Z-axis compliance to absorb coplanarity and tolerance stack-up across a large array, while the plunger's travel produces a self-cleaning wiping action, yielding a stable, repeatable contact resistance (CRES) in the milliohm range over tens of thousands of mating cycles. In AI and quantum-computing hardware these contacts appear wherever silicon must be proven or serviced: compression sockets for automated test, burn-in, and system-level test of GPUs, accelerator ASICs, and high-bandwidth memory, along with LGA sockets, board-to-board and mezzanine connectors, high-speed backplanes, and power-delivery contacts. Across a single rack that is hundreds of thousands of contacts, and across a hyperscale build, millions.
The Challenge
Conventionally, pogo-pin barrels and plungers are Swiss-screw or CNC-turned from stainless steel, beryllium-copper, or brass. That is a subtractive, one-part-at-a-time route that wastes bar stock, needs secondary deburring, and scales only with machine-hours. At data center volumes, the cost and weight of each pin add up quickly, and the machined approach offers little room to improve on either. The challenge was to deliver the same electrical, wear, and contact performance at a fraction of the cost and mass, reproducibly, at millions of parts.
The Engineered Solution
ProPlate applied its Plating onto Plastics platform to invert the economy of the pin. The body is produced as a net-shape, high-cavitation micro-injection-molded dielectric core and then fully metallized, so the electrical, wear, and contact functions are engineered into a thin plated shell rather than machined into the bulk. Because the conductive duty is carried by a shell only microns to tens of microinches thick, swapping the metal core for an engineering thermoplastic removes roughly 80 to 85% of the per-pin mass with no loss of current-carrying capability. ProPlate metallizes engineering plastics through two qualified routes, chosen by resin, feature scale, and volume, both converging on the same electrolytic copper, nickel, and gold stack: a PVD sputtered seed for even the most chemically inert resins, or an aqueous wet-chemistry seed suited to high-volume barrel plating. The stack is built electrolytically with a copper base, a sulfamate-nickel barrier for hardness and normal-force support, and a gold contact finish for low, stable CRES, with every lot verified by XRF thickness, ASTM B571 adhesion, and thermal-cycle and CRES validation. In a recent collaboration with a precision micromolding partner, ProPlate qualified the full stack on ABS and Topas (COC) micro-plungers, plating more than 5,000 pins in proof of concept with passing adhesion, documented under ProPlate's ISO 13485 phase-gate development methodology and ready to scale.
Benefits
- Approximately 80 to 85% Lighter Than Machined Metal
- Lower Unit Cost at Volume
- No Loss of Current-Carrying Capability
- Net-Shape Micromolding of Complex Micro-Features
- Qualified Cu/Ni/Au Metallization Stack
- XRF, ASTM B571 Adhesion, and CRES Validated
- Two Qualified Seed Routes for Any Resin or Volume
- Qualified on ABS, Topas® (COC), PEEK, Ultem® (PEI), LCP, PET, and PEBAX
Metallized Polymer Contact Pins for Wearable Insulin Delivery
Modern insulin delivery systems depend on millimeter-scale contact pins at the interface between the disposable fluid path and the durable electronics, where sweat and saline attack conventional finishes and machining is the wrong cost structure at tens of millions of units per year. ProPlate applied its Plating onto Plastics platform to metallize micromolded LCP and PEEK contact pins with a biocompatible gold-over-barrier stack. The result was connector-grade electrical performance and ISO 10993 biocompatibility on a molded polymer pin, qualified through two independent routes and documented to support the OEM’s design history file.
The Product: Micromolded Contact Pins for Wearable Insulin Delivery
Modern insulin delivery systems, including patch pumps and durable pump platforms, depend on millimeter-scale electrical contact pins and electrodes at the interface between the disposable fluid path and the durable electronics. These contacts carry sensing and drive signals for reservoir status, occlusion detection, and actuation, in a body-worn environment where sweat and saline attack conventional finishes. The requirements converge on a connector-grade solution: a gold contact surface over an engineered barrier and adhesion stack, with ISO 10993 biocompatibility and stable, low contact resistance for the life of the device.
The Challenge
Historically, contact pins of this kind are machined from stainless steel or brass and then plated. At insulin delivery volumes, which reach tens of millions of units per year, machining is the wrong cost structure. Micromolding combined with metallization replaces it with multi-cavity, seconds-per-cycle molding and mass-finishing electrodeposition. The opportunity is clear, but the substrates are not cooperative. A metallized polymer pin has to match a plated metal pin on contact hardness, wear life, and conductivity, and it has to do so on resins that were never designed to accept metal. The adhesion of the deposit to the polymer, not the plating itself, is the limiting factor.
The Engineered Solution
ProPlate developed this program on liquid crystal polymer (LCP) and polyether ether ketone (PEEK), two medical-grade resins at opposite ends of the metallization difficulty spectrum. LCP molds superbly at millimeter scale and responds strongly to aqueous surface treatment, while PEEK brings medical-implant heritage and mechanical margin but is among the most chemically inert engineering resins, with a narrow activation window. ProPlate metallizes both through two qualified routes that converge on the same verified copper, nickel, and gold stack: Route A uses a custom tumble-PVD sputtered seed to establish electrical continuity on even the most inert substrate, the geometry-agnostic development path and the preferred route on PEEK; Route B uses all-aqueous wet chemistry with an electroless copper seed, fully compatible with barrel mass finishing and engineered for production at tens of millions of pins per year. Both build the same stack electrolytically: a ductile copper foundation that buffers the CTE mismatch between polymer and nickel, a sulfamate-nickel barrier that blocks copper diffusion and carries contact load, and a hardener-free soft gold contact finish selected for the medical environment, biocompatible, tarnish-free, and compatible with downstream welding and wire attachment. Both the LCP and PEEK builds completed proof of concept with passing ASTM B571 adhesion and in-specification stacks, verified by XRF on every layer, with finished parts delivered to the medical device OEM partner. All work ran under ProPlate's ISO 13485 phase-gate development methodology, with documentation structured to drop into a design history file and support downstream design verification, process validation, and ISO 10993 activities.
Benefits
- Connector-Grade Electrical Performance on a Molded Polymer Pin
- ISO 10993 Biocompatible Gold Contact Finish
- About 80% Mass Reduction per Contact
- Lower Unit Cost at Insulin Delivery Volumes
- Net-Shape Micro Features Molded In, No Secondary Machining
- Mechanical and Electrical Parity With a Plated Metal Pin
- Two Qualified Routes to the Same Verified Stack
- Documented Under an ISO 13485 Phase-Gate Methodology
Frequently Asked Questions About Plating onto Plastics
Can any plastic be plated?
No. Plating on plastics requires a resin-specific process, and a resin that plates well is not the same as one that molds well. ProPlate® maintains qualified processes for ABS, Topas® (COC), PEEK, Ultem® (PEI), LCP, PET, PEBAX®, TPU, nylon, polyurethane, polyimide, and Noryl® (PPE/PS blend), and qualifies new substrates to specification on request. If your resin is not on that list it may still be platable, but it will require development work first.
How do you get metal to stick to plastic?
The polymer surface is prepared and made conductive, either chemically or by adding a seed layer using physical vapor deposition. Once the surface is conductive, the finish is built electrolytically. Adhesion is verified to ASTM B571.
What is the difference between wet chemistry and PVD seeding?
Wet chemistry activates the polymer surface chemically and suits high volumes of small parts. PVD deposits a seed layer physically, which works on chemically inert polymers that will not reliably accept a chemical activation. Many suppliers offer only the wet chemistry route, which limits the resins they can support. ProPlate offers both.
How much weight can plating on plastics save?
It depends on the geometry and the metal being replaced, but on programs we have run, converting a machined metal part to a plated polymer one has removed as much as 80% of its mass with no loss of current-carrying capability. Because the plated layer is only microns thick, most of the metal mass of the original part is what disappears.
Does a plated polymer part carry as much current as a solid metal part?
Yes, for the applications ProPlate® qualifies. Current is carried in the plated layer, not the bulk of the part, so removing the metal core does not reduce current-carrying capability as long as the finish is engineered to the application’s current-density target. Current-carrying performance is application-dependent and is validated as part of the qualification process for each specific program.
What metal finishes can you plate on plastic?
Copper, nickel, gold, platinum, silver, palladium, palladium-nickel, and tin-lead, on qualified polymer substrates.
What is laser direct structuring, and when should I use it?
LDS uses a resin containing a laser-activatable additive. A laser traces the exact pattern to be plated onto the molded part, and only the traced areas accept metal, which allows conductive traces and antennas to be applied directly to a three-dimensional component with no separate circuit board. It requires an LDS-grade resin, so it is not an option for every part. Conventional metallization remains the better route when the entire surface needs to be plated or when the resin is not LDS-grade.
Do you offer decorative or cosmetic plating onto plastic?
No. ProPlate plates plastics for functional performance only, including conductivity, contact resistance, catalytic activity, shielding, wear, and corrosion. We do not provide decorative or cosmetic finishes.
Do you plate medical polymer components?
Yes. Medical polymer metallization is handled under ProPlate’s Meta-Poly® platform, which has its own section of the site.
